Home > Hard Drive > Problems With Slave Drive Installation

Problems With Slave Drive Installation

Contents

If the drive still is not detected after testing the cables, contact your controller card manufactuer to see if there is an update available. Your motherboard might have some SATA II ports (running at 3Gb/s) and some SATA III ports. For specific details, see Answer ID 127: Error message: No mass storage device found is reported during installation of Windows 2000, XP, Vista, or 7. Reply Alan Bush says: November 26, 2008 at 11:12 pm At last!! have a peek at this web-site

To format the drive in Windows 2000 or XP, right-click on My Computer and go to "Manage". In addition I had to purchase a PCI serial ATA host controller card with a cable to connect the new HD. iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский язык Türkçe Machine translation Help Translate iFixit Close Power supplies may begin failing spontaneously and non-obviously, so this problem is always possible.

How To Slave A Sata Hard Drive

Current UltraATA cables with the 3 colored connectors do support this feature. You constantly get a message that space on drive c is dangerously low, which it is. NIce to see some floridians. WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2017 Western Digital Technologies, Inc.

  1. You should be able to see the drive in this list of boot devices.
  2. At startup, the computer will display all the devices detected on the system.
  3. In this edition of Hardware Upgrade, we’ll try and quickly squash as many common problems that we can.
  4. Select the type of format (NTFS or FAT32).
  5. Went OK.
  6. Should I try Cable select?
  7. Input the capacity of the partition and click on the Apply button.
  8. Supreme Court has a strict no-photography rule; the last known photos of the Supreme Court in session, taken without permission of the court, date from the 1930s.

Published 09/20/11 SHOW ARCHIVED READER COMMENTS (12) Comments (12) September 20, 2011 maxmeazle I've usually put all my IDE HDDs as cable select, the motherboard selects it as master or slave Win-7 Pro SP1 booted on my PATA (IDE) ST215A disk and installed a driver for new hardware, done OK. HDD The leading standard in enterprise capacity and performance SSD Flash-based storage for instant access to data Systems Building the highest performing and scalable data storage infrastructure possible ⎙Print ✉Mail Share How To Install A Second Hard Drive Windows 10 I cloned my 90GB IDE onto a 250GB IDE using a bootable HD Cloning CD.

Input the capacity of the partition and click on the Apply button. So now I have three SATA drives. Insofar as is possible, while the drive is still functioning, copy the important files to another hard drive or an optical disc. http://www.tomshardware.com/forum/271709-32-computer-problem-secondary-slave-hard-drive-deactivat Good job A+ on te article Reply RepairGal says: January 8, 2009 at 9:42 pm Anyone who doesn't understand what a "jumper" is shouldn't be trying to change out their hard

If installing two drives on the same EIDE (PATA) interface cable: Jumper the bootable drive as Master, and the other drive as Slave; then connect the Master drive to the black How To Install A Second Hard Drive Windows 7 If you are simply installing a secondary hard drive for storage, you don't have to make any changes to the configuration of your current hard drive. I upgraded the IDE with a SATA adapter(should I remove the jumper then?). Policies vary.

How To Slave A Hard Drive

Please try again now or at a later time. https://www.pcmech.com/article/installing-a-hard-drive-step-by-step/ When he’s not headbanging to heavy metal or geeking out over manga, he’s often off screen printing T-Shirts. How To Slave A Sata Hard Drive The connector on the left is SATA power, which not all computer power supplies have. How To Install A Second Sata Hard Drive Reply Alan Munro says: January 15, 2010 at 12:49 pm I am trying to replace my existing hard Drive with a Samsung 1Tb unit.

I believe this is a ATA-6 model. http://hcsprogramming.com/hard-drive/slave-hard-drive.php If you’re planning to use SATA, you can jump to the next step where we install the new drive. My hard drive crashed, but I had a back up one. It requires manufacturers to provide owners and independent repair businesses with fair access to service information and replacement parts. Master Slave Hard Drive Setup

After it boots OK, use Windows Management (right click on Manage from My Computer pop-up) to resize the new C: to include the remaining disk space I am sure smarter folks My hdd was very high sounding before it had been crashed. The Write Signature & Upgrade Wizard displays. Source Reply Mark barbee says: August 31, 2009 at 7:25 pm Here's one for ya.

Reply Robin says: January 18, 2009 at 9:00 am Nice guide, but you tell vista doesnt show the HD till you format it. Sata Master Slave It isn't. This may result in damage to the drive.

Attach the EIDE (PATA) or SATA interface cable: SATA Drives: The drive can be configured in one of two ways: Connected to

If you only have two IDE connectors on your motherboard, you’ll be forced to deal with jumper settings to get your drive to work.

September 20, 2011 SteveK Paul DL -- Ref image software, I've just discovered Macrium Reflect and so far can't find anything bad to say about it. About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center Skip to Main Content Search Help Tips Dictionary History Forums Contact You are here: Help > Hardware Makes sense, but I just didn't think about it. Slave Drive Computer I would like to use this computer to recover my data from a Samsung Spin Point (IDE) SV0813H, Hard Disk (XP) and a Seagate U Series 5 (IDE)ST340823A (ME) Hard Disk.

I owe you one. Once your data is connected, you can connect power to your drives. I'm now up to 1TB for more films!! have a peek here Note: Users installing an ATA/100 drive: Windows 2000 by default does not support ATA/100 data transfer rates.

Please disconnect any other hard drives from the computer system until Windows has been completely installed on the desired hard drive. When a hard drive exhibits problems, your only goal should be to rescue your data from that drive. PlayStation Vue: How Do They Compare? rebooted PC and in Bios saw and selected to boot from the WDC WD5000AADS device.

Adding Second Drive: Click the Start button and then access Control Panel -> Administrative Tools -> Computer Management -> Storage -> Disk Management. Your drive's label will show the exact jumper settings your drive supports. Please contact your system or RAID controller manufacturer for assistance on defining your drive in a RAID Array. Reply Nick says: August 22, 2009 at 4:15 am awesome.