Home > Hard Drive > Reinstalling OS To SATA Drive With IDE Drive Installed

Reinstalling OS To SATA Drive With IDE Drive Installed

Contents

Please help. Make sure the motherboard in the computer can support the type of drive that you want to install. Windows 98 or ME If the disk is not already prepared, partition the drive and format it to FAT32 using the FDisk utility. If your using Windows 9x (why?) then you'll want to check out bootdisk.com and find something that'll cover your needs. http://hcsprogramming.com/hard-drive/transferring-files-from-a-laptop-sata-drive-to-a-desktop-ide-drive.php

The IDE HD had to be on the secondary IDE cable in order for it to be recognized by the sata drive. I only noticed it because it was on the latest list and easy to get to.Think it over.Bob Flag Permalink This was helpful (0) Back to Storage forum 29 total posts Follow the on-screen instructions. I tried to re-set boot priority and drive priority, but I get the same thing. look at this site

How To Connect Ide Hard Drive To Sata Motherboard

That mistake recognized and rectified, I still cannot figure out why XP won't load under my current setting.The BIOS settings have been set so that SATA 0 is the drive to Especially if additional components like memory or a CD or DVD drive were also added. Sometimes it woudl boot up and sometimes it wouldn't.

The cramped 3gb left on my drive will no longer bog me down or limit my media. The install disk comes on a floppy so if you don't have one then you'd better be able to do a BIOS update. But itโ€™s not going to be easy. Seagate Ide Hard Drive Jumper Settings Fasten the screws to secure the side panel.

Once you remove the cover and decide where and how you will physically install the drive, take the following steps: 1. Ide Hard Drive Jumper Settings Or is there another way around this? BUY NOW FREE TRIAL PARTNERS Partners Become a Partner Locate a Reseller Partner Programs > How to > Computer Instruction > Install IDE Hard Drive Install IDE Hard Drive 2016-08-05 TechSpot is a registered trademark.

If you don't want to reinstall Windows, you can clone the contents of your old hard drive to your new one using the setup utilities that hard drive manufacturers provide, or How Many Hard Drives Can Be Connected To A Single Ide Cable Find out who represents you in Minnesota's legislatures. This is where almost all headaches and problems came in. This allows the cable to select if the drive is master or slave based on the position on the cable.

  1. I was able to use the existing power cable.
  2. It was driving me crazy.
  3. Setting Jumpers: SATA Drives Good news!
  4. Boot from the Ultimate Boot CD, and select the utility you want to use to clone the drive.
  5. The problem I had in doing this was that I had to assign a drive ltter to the new drive in order for Ghost to recognise the destination drive.
  6. Your PC will barely realize that anything has changed.
  7. Leave the cover off for now, and give the system a quick visual check to make sure that everything is connected properly.

Ide Hard Drive Jumper Settings

More about Hard Drives 0 Comments Add Comment Add Comment 1024 View Statistics: Past 24 Hours: 9 Past 7 Days: 55 Past 30 Days: 230 All Time: 5,803 24,954 Free Manuals http://www.tomshardware.com/forum/254930-32-installing-sata Getting it ready for use takes a little longer. How To Connect Ide Hard Drive To Sata Motherboard Nothing showed in Windows XP at all-didn't show up in disk management either. How To Connect Ide Hard Drive To Motherboard Assign the drive letter.

In the BIOS, the system is recognizing the other HDD's connected to SATA 1 and 2 without a problem.SATA 1 has my old image on it (also XP), and when I his comment is here Is there a way that i can create an image of the 40gig and still have my 250 gig unammended? Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. Visit now Z7_3054ICK0KGTE30AQO5O3KA30H4 hp-feedback-banner-portlet Actions ${title} Loading... How To Install Ide Hard Drive

Reply tysun says: August 12, 2007 at 5:44 pm I install a Sata WD drive into my w2k pc. If not, you can extend it using a controller card just the same way as with IDE. I can pull it out by just removing 1 screw. http://hcsprogramming.com/hard-drive/vista-installed-hard-drive-acting-odd.php Format the drive.

Once it loads, you should see an "Initialize Disk" wizard pop up. Sata And Ide Hard Drives Together Cheers Ernie Reply Joshcore says: July 31, 2007 at 11:04 pm Well done, Ernie ๐Ÿ™‚ Reply William says: August 3, 2007 at 6:08 pm Hi Joshcore thanks for the advice, I Look for where the SATA ports are set up.

i have windows xp so it is not showing up on my computer.

If the new drive is not displayed or shows no usable space, continue with the next step to format the drive. I would also check under Integrated Perpherals in the Bios that your IDE set up shows the Serial-ATA controller is enabled. My HD crashed so I purchased a new SATA drive. How To Install A Second Hard Drive Figure : Finding the BIOS version On the System Information screen, find the BIOS version.

Wow again thank you Reply Eric says: October 13, 2009 at 11:16 pm Great instructions. Software Installation/Cloning Now that your new drive is installed, we can move on and get it set up with Windows. Before, the cd and dvd drives were e: and f:, the hd(when it was recognized) was still g:Not sure why it happened (I might try removing all emulation drives first and navigate here On some cases, it might be necessary to remove the front of the computer so that you can remove the drive cage.

Alternatively, use a diagnostic program such as Everest Home Edition to determine the current configuration of your drives and interfaces.If you are also installing a PATA or SATA interface card or by tubaloth / June 1, 2006 3:55 AM PDT In reply to: Mixing SATA and IDE drives in a system? Do NOT choose RAID unless your mobo forces you to do that for any unit that is not IDE. Tell it to install the NTFS File System unless you really know you need FAT32 for some reason.

Reply Mark barbee says: August 31, 2009 at 7:25 pm Here's one for ya.