Home > Hard Drive > SATA & IDE Drive Problem

SATA & IDE Drive Problem

Contents

Whenever possible, known good parts should be used to replace any suspected bad parts before ordering replacements. Return to Diagnostic Chart Does the hard drive spin up? Make sure the connectors are clean and tight. IDE hard drive is not recognized by the system BIOS If the drive is not recognized by the system in the System Summary section of the System Configuration Utility (the BIOS), http://hcsprogramming.com/hard-drive/transferring-files-from-a-laptop-sata-drive-to-a-desktop-ide-drive.php

so it installed onto C: and put a windows folder on D: as well as the stuff already there.that just blew my mind so i thought i better get sum help>i Return to Diagnostic Chart SSD State Drive (SSD) drive? I didn't want to re-install windows (until vista) and then I might switch things around. Connect the gray middle connector to the Slave drive. check my site

How To Connect Ide Hard Drive To Sata Motherboard

Remove the drive from the chassis and operate outside the chassis to eliminate possible heat and electrical shorting problems. Browse other questions tagged hard-drive sata pata or ask your own question. I have to thank this guy for the idea on how to fix this.I guess I would have tried that at some point, but at least now I know I’m not

SATA is actually closer to SCSI then to IDE. Microsoft Operating System Installation Instructions For further detailed information about “How to partition and format a hard” refer to the Microsoft Knowledgebase Article references below. Operating system considerations It is important to not confuse operating system limitations with hard drive problems. Ide Hard Drive Jumper Settings Guys I need some quick help.

Please check the compatible system listing to confirm the diagnostic will work on the particular machine. Sata And Ide Hard Drives Together If the drive uses sound and vibration insulators, use a screwdriver or install a jumper wire between the drive and chassis to ensure the drive is fully grounded. I just rebuilt my PC using an ASUS A7V880 Mobo, AMD AthlonXP 2800+ with 1Gb RAM. recommended you read I can boot off the SATA only if I have no IDE drives attached.

I have had both dual boot on the same HDD,but on diferent partitions and also on two serarate HDD's with either both seen within the bios or with one pair of How To Make Ide Boot Instead Of Sata Now, neither drive is showing up in My Computer. The boot hard drive should always be the Master on the primary IDE interface. They said that the problem is because my windows is installed on the IDE im having this problem.

Sata And Ide Hard Drives Together

That way it will recognize your Sata drives and install Windows on the drive you select to be the boot drive.I would advise disabling IDE Hard Drives by temporarily removing their Discover More This may be caused by a corrupted file or the hard drive may be bad. How To Connect Ide Hard Drive To Sata Motherboard Some move a drive like that and hope the software keeps running (from the old drive). Ide And Sata Drives In Same Computer Self-Monitoring, Analysis and Reporting Technology (SMART) is basically a predictor of doom, though it's up to you whether or not to heed it.

If you're just looking for faster boot time, a SATA 3 SSD may make more sense. weblink Due to somewhat inconsistent operating system support, a firmware upgrade might be necessary after an automatic Windows update, or for compatibility with a particular high performance application. Please provide a Corporate E-mail Address. For the main part, you troubleshoot SSD devices the same way you would any device with the same interface. Motherboard With Ide And Sata Ports

So the device manager entry is correct. SATA is actually closer to SCSI then to IDE. No problem! navigate here The SSD firmware controls the relatively high burden of housekeeping tasks that the SSD drive must perform independently of the PC, especially wear leveling and other tasks that will extend the

The ribbon cable connectors must also be seated all the way into the IDE port on both the drives and the motherboard, or adapter card if you are using a RAID What Are The Two Goals When Implementing A Raid Solution Your computer may automatically detect your new drive. Recover We can Recover your Files, Just in Case.

Flag Permalink This was helpful (2) Collapse - Should not be a problem by xpostal / July 22, 2005 1:49 AM PDT In reply to: Mixing SATA and IDE drives in

  • SearchCloudStorage Showback the value of your data storage expertise To demonstrate value, IT must provide an easy-to-understand cost model to its business leaders.
  • Convert all partitions on IDE HDs to extended. (This option maybe optional)2.
  • I have an Intel motherboard with two built in IDE controllers and two built in SATA controllers.
  • SearchDataBackup StorageCraft backup diversifies, acquires Exablox object storage StorageCraft backup targets server-based storage.
  • This makes it easy to add Serial ATA compatibility to your existing system without removing existing Parallel ATA disk drives.
  • Make sure the computer is plugged in and listen for the power supply fan.

SATA drives don't "daisy chain" and each one needs a separate data connection to the controller. The buy gives HPE an installed base, ... This is done as a backwards compatibility mode for other OS's or lazy installers. How Many Hard Drives Can Be Connected To A Single Ide Cable IDE->SATA DVD drive problems, 4 pin connector doesnt fit.

Try the hard drive in another PC or a USB shell before you conclude that it's dead. Running it in AHCI mode will enable NCQ (if the drive has it) and hot swap, if the chipset also supports hot swap.*WARNING*Do not switch the BIOS from IDE to AHCI Don't worry if the system thinks your new drive is SCSI. his comment is here I have Windows 2000 with an AMD 2800 chip and A7V8X mobo.

Use ScanDisk to check the drive for bad sectors and other problems that may interfere with its operation. If the problem stays with the original computer, suspect the cable or system board. Magento Last 7 days Order Would descendants of Earth people stranded on another planet eventually forget about Earth? ABOUT About Us Contact Us Discussion Forum Advertising Privacy Policy GET ARTICLES BY EMAIL Enter your email address to get our daily newsletter.

The connectors aren't soldered to the wires, the circuit is made mechanically with "V" shaped contacts forced through the plastic and digging into the conductors. makaveli2007Feb 2, 2011, 9:50 PM Hawkeye22 said: AHCI drivers should have been included with your motherboard if you did this as a home build, otherwise you can probably find them on