Home > Hard Drive > Troubles Connecting 2 SATA Drives

Troubles Connecting 2 SATA Drives

Contents

There should be no problem in connecting a SATA and IDE drive, although it would be best to install the SATA as the main drive. It’s yours. Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. I can boot off the SATA only if I have no IDE drives attached. check my blog

The easy stuff first: Check to see that your cables are well connected, and properly seated. Once your data is connected, you can connect power to your drives. although its too late. How to build a private storage cloud Building internal cloud storage must account for elasticity, choosing the right platform, allowing for workflow, and stack ...

How To Connect Sata Hard Drive To Motherboard

A particular file may be corrupted on one copy but readable from another. These are usually one of these: Delete, F1, F2, F3, F5, F10, Esc, or Insert. I installed Windows on the SATA drive.I built this computer myself and haven't had any problems with this configuration. And lastly, watch to be sure you don't loosen something else while you are working on the current cable, or you might create a loose connection you don't know about.

  • Since the operating system does not require a fresh installation, preparing your drive for use is easier.
  • The first screen you see after POST will usually say something like “press Del to enter BIOS.” You may have to look around in some of the other menus, depending on
  • Connections Have the appropriate cables on hand.

Power PC and Cooling (http://www.pcpowercooling.com) and other vendors offer power supplies designed specifically to replace proprietary units that are incompatible with the standard power supplies available from big-box stores and other Selected the “boot” flag, rebooted to Bios, selected to boot from WDC WD5000AADS device, OK. Forgot your password? How To Install A Hard Drive In A Laptop I had to rename my drives to a drive letter beyond the H drive.

Dell Bios Boot Sequence by Clive Darr, available under Creative Commons. For an SATA drive, any circuit board failure makes it difficult to access the drive, because every SATA drive acts as its own disk controller. Narrowing down the problem with your SATA drive Like any other kind of troubleshooting, a methodical approach is best for finding problems with SATA drives. useful reference For the last 20 years, he has been a freelance writer specializing in storage and other computer issues.

Computer won't boot from primary HDD Boot issue on Windows 7 won't start after installing an extra [empty] hard drive Windows 7 won't boot after installing new hard drive After installing How To Connect Sata Hard Drive To Usb Best answer PaperdocApr 15, 2009, 2:54 AM You start with "For a time now ..." This sounds like an intermittent problem that has become worse until you fixed it.The most common TechSpot is a registered trademark. Take a look at this: http://www.howtohaven.com/system/change-disk-signature.shtmlIf you can install the drive in another computer and check its ID and compare to the boot drive you would know for sure.

Install Seagate External Hard Drive

There are a few additional considerations to take into account if you are running multiple SATA drives in a RAID array (like making sure all OS's are installed with RAID drivers) http://www.techspot.com/community/topics/troubles-connecting-2-sata-drives.28194/ The drive warms quickly as it runs, so if this method succeeds you may need to do multiple freezer sessions to recover all of your data.Finally, as a last resort although How To Connect Sata Hard Drive To Motherboard While installing the drive, wear a wrist strap and cable connected to ground.Turn off the power to the host system during installation.Do not disassemble the drive. How To Install Seagate Hard Drive On Pc Thanks Mike Jul 6, 2005 #1 patio TS Maniac Posts: 482 Try the known good drive on SATA 2 by itself...Does this change anything ? ?

You may have to install drivers for the disk before using them. click site I made my S:partition a tad larger in case I need to use other imagers. 6. If the system still can't find the drive, make sure you have the latest version of the controller firmware and computer BIOS. If you can install your system disk on its own IDE cable, set it to single disk master mode (sometimes achieved by removing the jumper) and install other disks and devices What Is Sata Hard Drive Mean

I'll disconnect / re-connect every cable I can find at both ends.Just be careful of a few things. Find out who represents you in Minnesota's legislatures. And if it does not work after all your "cleaning" actions, look closely again to see if there is an unrecognized loose connector. news Submit Your password has been sent to: By submitting you agree to receive email from TechTarget and its partners.

by rbird / July 22, 2005 11:48 PM PDT In reply to: Mixing SATA and IDE drives in a system? Install New Hard Drive Windows 7 Finally, I disconnected the power to the ST215A, booted and voila! “no NTLDR found”. It was driving me crazy.

I'm having the same problem...

If a connector has been irrevocably damaged, you might not be able to use it for your drive. If the drive is functional, the best solution is to use a drive wiping utility before you discard the drive. The important thing to recognize here is that IDE drives have an illustration of how to set up the drive properly before installation, and you have to read that before installing. How To Install Seagate Hard Drive On Xbox One Is there something wrong with my hard drive that is can't continue to load?

I will not describe here the many permutation at the Bios level that I went thru. If so or not Why, and as many reason as possible Why? Set system disks to master, and other disks to slave or cable select settings. More about the author What happens if you only have your second drive attached, if it has no OS it won't try to boot but does it still crash your system or will it post

If you’re planning to use SATA, you can jump to the next step where we install the new drive. by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system? No problem! The best way to secure your files against loss is to back them up regularly.

Please refer to our CNET Forums policies for details. solved Problem connecting Notebook's HDD to SATA cable. Using Ghost 15 or Windows Repair disk run chkdsk /f on the new C: partition 4. Any News Is Bad News If a hard drive shows even the slightest sign that it has problems, immediately copy the data from that drive to another hard drive or optical

it shows in the bios option, but goes no where when try to boot or install windows weird problem, windows wont boot when restarted ,even with the new hard drive or Temporaly desativate secondary IDE Channel, while installing windows on HD SATA, because windows insist in write MBR both HD SATA and old IDE boot HD.4.