Home > Raid 0 > Recover RAID 0 Stripe Array After Motherboard Failure?

Recover RAID 0 Stripe Array After Motherboard Failure?

Contents

The Ext drive case/controller is was thinking of purchasing was the Startech.com 3.5 inch eSATA USB Dual SATA External RAID Hard Drive Enclosure I note that there is software called raid I recommend in the future to get a 3rd HDD to use as storage. There is a software product that you might be able to use. The onboard RAID controller was a WinXP Promise FastTrak 378 (tm) Controller/WinXP Promise RAID Console SCSI Processor Device Motherboard was an Asus A8V Deluxe (5 PCI, 1 AGP, 4 DDR DIMM, http://hcsprogramming.com/raid-0/raid-0-array-is-broken.php

System restarted after firmware installation and SATA ports were reset to AHCI mode. Recover raid 0 failure Dns-323 recover from raid 0 disk failure RAID 0 Hard-drives - how to recover? The new mobo uses different SATA drivers. (Message edited by PatsFan on September 23, 2006) 2 9/23/2006 (11:32 pm) by patsfan patsfan (4 Posts) Hi all, I'm new this forum Alternatively you may just not be aware of who makes the controller for your specific drive. http://www.techspot.com/community/topics/recover-raid-0-stripe-array-after-motherboard-failure.122001/

How To Fix Raid 0 Failure

However, if your purchase your new motherboard from the same manufacturer, can (or has anyone) you get your data visible/usable? I couldn't locate the same make and model for replacement. And then plugged it straight into completely new hardware and had it all "just work".

nag nag nag backup backup backup etc. Files are broken into stripes of a size dictated by the user-defined stripe size of the array, and stripes are sent to each disk in the array. The electronics on one of the disks has failed. Recover Raid 1 DFI X58-T3EH8 | I7-920 [email protected] (V8) | 6*2GB Corsair Dominator @1800-7-7-7-18 | eVGA GTX 970 |120Gb SSD in RAID 0 (456Watts) Main Server (WIP): DFI X58-T3EH8 | I7-920 [email protected] | 3*2GB

The RAID contoller on the old mobo was Promise, the new one is different. Raid 0 Recovery Software If the detected configuration is correct(4) , press Enter to continue to the next screen, and choose Write to update the partition table as shown.Part 3: Correcting the Master Boot Record5. share|improve this answer answered Sep 2 '09 at 12:46 nik 44.5k776125 Yeah, the bolded part is kicking me in the a.s :( But good to know about the mentioned http://www.tomshardware.com/forum/245428-32-recover-raid-failure Went from a Gigabyte to a DFI and it did not want to work.

Please turn JavaScript back on and reload this page. Raid 0 Failed After Bios Update Why does cout print "2 + 3 = 15" in this snippet of code? everything has been unplugged for weeks. The motherboard on my PC failed about a week ago.

Raid 0 Recovery Software

The array volume name probably doesn't need to be the same, but I wouldn't risk changing it.Part 2: Recovering the partition tables in TestDisk (or other partition recovery software)3. It will merely create a copy of your RAID at another location. How To Fix Raid 0 Failure Overclockers Community Newsletter -- OVC -- Default Mobile Style All times are GMT -5. Raid 0 Array Failed I tried File Scavenger and it wants me to run the drives not in raid mode so that windows would see them as individual drives.

share|improve this answer answered Sep 2 '09 at 12:44 Josip Medved 7,71111937 1 huh, I hoped that there is some tool to fix the mbr records on the disks, and his comment is here I really don't want to loose all of the data I have stored on these drives. i.e. I am not aware of any tool that can come even close to untangling that mess and even if there was such tool, you can hope for 64K block recovery topmost. Raid 0 Failed To Boot

If thats the case it does not matter what h/w you try and use, your chances are not good. Hot Network Questions Why is 7 the most feared number? And surly, I know it was stupid to put the disks in RAID 0 and store data on them :( hard-drive data-recovery share|improve this question edited Jan 12 '11 at 12:07 this contact form I disabled RAID on my motherboard (which uses P45/ICH10R chips), enabled Legacy SATA mode, and powered down.

I would like to add two further points of information if I may:Point # 1After and only after the completion of the recovery of the partitions (Step 4 on your guide), Raid 1 Failure You cover my core questions, as well as related issues (RAID <> backup). Yep, that'd be your best shot but any nForce4 MB should work. My System (13 items) CPUMotherboardGraphicsRAMIntel 920Asus P6T + LSI 9240-4i SATA6GB/s cardNvidia 8800GTSPatroit Viper 6GB of

No it will not in many cases with huge disks or with SATA drives and hardware failure on a drive.

easy and cheap to set up). Each of these has associated risks and ease of replacement if the broken item. Why is it a bad idea to use Same Page Tool as a survey? Raid 1 Drive Failure Recovery Dijkstra path finding in C# is 15x slower than C++ version How can I avoid being "the negative one" when giving feedback on statistics?

E8400 Gigabyte GA-EP45-UD3P 2 Gig Crucial Ballistic 6400 Radeon HD4850 - Athlon 64 3000 939 DFI Lanparty Ultra D 1 Gig Corsair CMX4400C25 Geforce 7800 GT Reply With Quote 01-22-10,06:37 PM share|improve this answer answered Apr 19 '13 at 15:40 Reid 2833416 add a comment| up vote 1 down vote I guess you understand that RAID-0 is just striping the disks, there S/W RAID (as implemented in Windows, Linux, etc) means you not dependent on the peculiarities of the hardware RAID controller. navigate here Why are Linux system call numbers in x86 and x86_64 different?

This of course hinges on the fact that array data was also stored on the drives and not just in the RAID BIOS. I don't want to purchase the same board if possible, as I wish to move to an I7 based PC. As Igor points out he had both halves of the data; the physical drive (1) and a drive image (2).