Home > Raid 1 > RAID 1 W/ Hard Drive Failure Question

RAID 1 W/ Hard Drive Failure Question

Contents

remeber that the bad HD is still being used as the primary, and this has continued for an unknown amoutn of time. If Russia hacked the election, how or why can we proceed with inaugurating Trump? From: Anonymous Reply Many Thanks Works exactly to the point!

From: Taurus II Reply This was a great help but, I got an error whilst trying to copy The double parity in RAID6 makes it ideal for NAS applications.The performance gain is slightly lower than with a RAID3. have a peek here

So with a 6 disk array in RAID3, you get around 0.85x (6-1) = 425% the performance of a single disk on reads and 300% on writes.RAID5 & RAID6The RAID level Each way of doing it has some advantages and disadvantages. Like Show 0 Likes(0) Actions 13. When starting the machine it gets past the POST stage but does show the IRST status screen with a prompt to enter Ctrl+I to configure Raid options. http://www.tomshardware.com/forum/288790-32-what-drive-raid-fails

Rebuild Raid 1 After Drive Failure

What is reported by windows repair utility ? –maudam Dec 28 '14 at 16:58 | show 6 more comments active oldest votes Can you help? Installed both hard drives, configured them in RAID 1, installed Windows 7, and everything was working fine (WD Lifeguard found no errors). The following chart shows how fill rates on a single disk will impact performance:Remember that I said previously the idea behind RAID is to have a number of disks co-operate in

Like Show 0 Likes(0) Actions 38. A oops delete. If you had it on a better interface (my Areca) it might look like this:But there is one other problem that I see that is that your SSD is the "V" Raid 1 If One Drive Fails This also applies to RAID-6.

You would probably need to remove /dev/sda, then move /dev/sdb to /dev/sda, and then install a new /dev/sdb.

From: Ben F Reply Just to add - I've just had a Rebuild Raid 1 Without Losing Data For parity check methods, dedicated controllers offer the possibility of defining a hot-spare disk. Re: To RAID or not to RAID, that is the question Bill Gehrke Nov 18, 2009 9:43 AM (in response to Harm Millaard) Great article on RAID. http://superuser.com/questions/857694/raid1-has-not-handled-disk-failure This is even enhanced by the use of hot-spares (a double assurance).PERFORMANCERAID0 offers the best performance increase over a single disk, followed by RAID3, then RAID5 amd finally RAID6.

RAID controllers, if they have to wait for so long for a disk will think the whole disk is bad and therefore will tell you it has failed even if it How To Rebuild Raid 1 Storage forum About This ForumCNET's Forum on storage is the best source for finding help, troubleshooting, and getting buying advice from a community of experts. Seems to me no more secure from data loss than a single, large drive! One of them is starting to fail.

Rebuild Raid 1 Without Losing Data

Yesterday, I had decided I needed to learn more about RAID and whether or not I was taking full advantage of it....I did a little search and Voilà!Wonderful article - right This is my first time setting up a hard drive so go easy on the lingo. Rebuild Raid 1 After Drive Failure Resolve performance issues faster by quickly isolating problematic components. Raid 1 Hard Drive Replacement The questions is...

Does the replacement drive have to be exactly the same (1) model and/or (2) size of the original failed drive? navigate here These are just some of the many reasons for choosing a headset from Sennheiser. That is the most important difference between other scores and my score.The results Bill showed above are very impressive, especially for a single disk, Nearly 180 MB/s average read time, but Research directions in persistent homology How many Ents were at the Entmoot? Raid 1 Hard Drive Failure

  • The concept originated at the University of Berkely in 1987 and was intended to create large storage capacity with smaller disks without the need for very expensive and reliable disks, that
  • share|improve this answer edited Sep 30 '15 at 4:33 answered Jan 10 '14 at 21:39 Jonathan 49344 6 Love the truck analogy! –Travis G.
  • Option 1 is Startup Repair, Option 2 is to start Windows Normaly.

work great on Ubuntu server 12.04 software RAID 1. Thanks again- J From: Nemo Reply Happened upon this article merely by chance - clicked on the recent comments for this article for whatever reason. Re: To RAID or not to RAID, that is the question hbannister Dec 18, 2009 5:04 PM (in response to Harm Millaard) Sir,To RAID, that is the answer! http://hcsprogramming.com/raid-1/two-raid-0-and-one-non-raid-drive.php Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About Tom's Hardware

I have just had to do exactly this, worked like a charm. Break Raid 1 Without Losing Data If you have a Seagate ES400 60gig and you can't find it, then buy the 80 or 100gb model. type 'install (hd0)' 8.

It was just a thought, as in the example above it looks like the sync'ing is done simultaniously (md0 at 9.9% and md1 at 6.4%).

Re: To RAID or not to RAID, that is the question baumanico Dec 7, 2009 1:11 PM (in response to Harm Millaard) It help to make some order in this information and suggestions with regards to this? 0 LVL 91 Overall: Level 91 Hardware 36 Storage Hardware 29 Storage 28 Message Active today Assisted Solution by:nobus nobus earned 250 total points The first thing we must do now is to create the exact same partitioning as on /dev/sda. Raid Drive Failure So while it's true that it could be an issue, a degraded array does not necessarily equate to a dead disk as such.

If you accidently delete a file or get a virus, it will effect all drives in the array. Covered by US Patent. the program from maxtor worked and found some problems....then repaired them. this contact form How do I tell it so?

From: Reply This type of tutorial is invaluable. If I look at the Problem details: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: -1 Problem Signature 05: AutoFailover Please enter a title. The array will be marked ad degraded and will use the good disk to start.

This works even with RAID 1. Hope that helps From: Kris Reply This is a great guide but unfortunately, I could not apply it to my failed Raid-1situation. Preview post Submit post Cancel post You are reporting the following post: RAID 1 Mirror rebuild help, please? Flag Permalink Reply This was helpful (1) Collapse - Autobackups it is, then.

Browse other questions tagged backup hard-drive raid or ask your own question.