Home > Raid 1 > Raid Drive Troubles

Raid Drive Troubles

Contents

Nvidia 8800GTS Card I keep getting Blue Screens of Death ever since I built it. It works for some people and doesn't work for others. Reply Jasper J says: November 24, 2008 at 5:39 am Well if you can shove that old drive in the freezer (try putting it in a container and hope you get The only time it will fail is when two disks failed simultaneously but such probability is one in a million! http://hcsprogramming.com/raid-1/two-raid-0-and-one-non-raid-drive.php

Share This is the process to obtain a replacement hard drive and swap the failed drive. I had the machine up for about four hours, then as I was creating my post I noticed things slowing down. Reply PCMech says: August 14, 2015 at 9:09 pm Hi Mike - Thanks for your comment and welcome to PCMech! I hate to buy a new hard drive if that is not the issue.

Raid 1 Hard Drive Failure

There are two types of sectors, a hard and soft sector. ALL Rights Reserved. System Model: 0WG855Processor: Intel(R) Core(TM)2 CPU 6300 @ 1.86GHzBIOS Version/Date: Dell Inc. 1.0.3 , 08/14/2006Language: ENUIntel(R) RAID TechnologyIntel RAID Controller: Intel(R) ICH8R/DO/DH SATA RAID ControllerNumber of Serial ATA ports: 6 RAID Reply Aaron says: November 15, 2007 at 11:13 pm I just built a new AMD system running Windows XP SP2.

raid hard-drive hardware-raid share|improve this question edited Aug 20 '09 at 15:46 asked Aug 20 '09 at 15:25 Matias Nino 85742140 2 What OS? Intel Matrix Storage Manager can then rebuild the array.I have had luck using the steps above on a "failed HDD;" it rebuilt the array, but failed again. There are different softwares for checking this like Hdd Health crystal disk info. Rebuild Raid 1 Without Losing Data So if the complete format is the only choice that is left, then one have to take proper backups of the data and then can go for the full format.

As a result, one may tend to believe that RAID can not fail. Raid 1 Hard Drive Replacement Regards, May Reply Gloria says: October 1, 2007 at 4:54 pm I have noticed that my files are becoming slower to load, but now there is a pop-up message that constantly Usually takes 1-3 minutes to get off the "welcome" screen. *Accessing documents, websites, email, etc. http://www.tomshardware.com/forum/253487-32-failed-hard-drive-raid Thanks for sharing.

So during this time it is better to allow the hard disk to complete its earlier work, and retry the operation a little while later. Rebuild Raid 1 After Drive Failure Here are 6+ signs it might be dying 2,802 views | 0 comments Hard drive failing? NOTE: when using a RAID setup, all drives must be identical. i passed antivirus and tested some of the HD and not have bad sectors, when i tested with hd recovery only gave me a lot of "delays".

  1. Ja Nein Schicken Sie uns Ihr Feedback.
  2. I did extensive diagnostics with Spinrite and WD Diag on each drive and they picked up NO surface issues, no sector errors, and no SMART warnings.
  3. To re-establish data mirroring and restore data redundancy, refer to the procedures below.Missing Member1.
  4. That's why I sent the 1TB external seagate back for a free replacement.
  5. Power on the system.
  6. Whenever it gets busy in doing some important mechanism within, it's external command following becomes extraordinarily slower.

Raid 1 Hard Drive Replacement

Reconnect your PC's power cable. http://www.dell.com/support/article/us/en/19/644652/en The status in the information pane will display 'Rebuilding % complete'. Raid 1 Hard Drive Failure This can usually be done by visiting the manufacturer's website, looking up the returns/warranty section, and entering the serial number of the drive. Intel Rapid Storage Technology Raid 1 Degraded AMD Athlon 64X2 6000+ I have 2 gigs of Corsar Ram (YES,in the right slot.) 4 SATA hard drives (hooked into the MB in their numbered slots.

This happens with any one at his or her house. http://hcsprogramming.com/raid-1/raid-died-while-swapping-out-a-failed-drive.php You can generally follow all of the steps above to diagnose the problem, though SSDs generally don’t produce noises when they’re going bad. Scenario 3: Frequently, due to power surge, the controller or a number of disk elements could fail resulting in total loss of data. Important: REMOVE YOUR PC's AC POWER CABLE to insure there is no electricity flowing to your PC. Failed Raid Volume Detected Recover Volume

The rebuild process can take several hours depending on the size of the drive being replaced. My main gripe is all the save game progress. Bitte versuchen Sie es später erneut. Check This Out eventually windows does open a check disk shows everthing to be fine.

Then there are failures that cause bad sectors that isnt a problem with physical damage, but just the magnetic fields for the 0 and 1 being weak, this is rare today Failed Raid Volume Detected Recover Volume Raid 1 solved RAID 1 Data Confirmation on 2nd hard drive solved What is the best, most reliable hard drive for raid 1. It doesn't mean the drive is good, just that the BIOS can see it.

Be sure to head on over to the PCMech forum and post your problem to get some additional help from the PCMech community!

Because of having seen this article above, when I was experiencing freezes frequently starting in November, I finally bought a couple of Seagate 1 TB external backup drives and started backing It was of 3 TB HD. He or she may be astonished to see that, and may definitely think that his or her all data are lost. How To Rebuild Raid 1 Intel Rapid Storage Both Samsung and Seagate are useless as supporters of their products as it is impossible to contact them for assistance.

At the same time, it's worth popping into Device Manager and checking that your controller/motherboard isn't going through any issues or failures, as it's entirely possible that the problem isn't even You have a limited number of read/write cycles. Well i hope that u can help me, i only want to be sure that is the HD for sending that to warranty. http://hcsprogramming.com/raid-1/raid-1-w-hard-drive-failure-question.php When i boot the pc up i get a message saying press ctrl and f to enter raid setup utility so i do this here i can delete the array or

With the power OFF - UNPLUG the power cable to the computer - by re-seating the SATA connectors into the mobo and the HDD; do the same with the HDD power The first step is to insert the OS drive in the computer through external devices or through CDs or DVDs. Please learn from my mistake and backup your Western Digital Drives with anything else before it is too late. Our experts there would be more than happy to assist you.

Terms of Use Privacy Policy Licensing Advertise International Editions: US / UK India Home Premium New Files VCE Simulator Upload VCE File Request Exam Contact FAQ Login/Register Practice Exams: Microsoft VMware