Home > Turn On > T Series Emachine Wont Start

T Series Emachine Wont Start

Contents

Swapped out power supply. I took it back to Comp USA and they gave me a new one. Have you tried a different monitor. 0 Discussion Starter jwright68 9 Years Ago Is the monitor on? The funny thing is, I rebuilt a friends machine for him, and he gave me his old MB, CPU, RAM, graphics card, which is all higher spec than what I already http://hcsprogramming.com/turn-on/vdu-wont-display-anymore.php

Does that have anything to do with the problem? 0 TT4Titans 5 8 Years Ago Go into your BIOS and change the boot order to just HDD. The hard drive, memory, CPU, cpu fan, optical drives are all good. Have you tried doing a CMOS reset? Logged raywaterbugTopic StarterGreenhorn Experience: Beginner OS: Unknown Re: emachine won't boot up « Reply #9 on: January 31, 2011, 04:05:21 PM » Yes everything seems to work, thanks for your help

Emachine Desktop Wont Boot Up

I posted a list of my current hardware earlier in the thread - is a 450w adequate for that setup? I found that I can get it to boot by hitting the F8 key as-soon-as I see the HD activity light come on. It found the hd with numbers and os in brackets, I then chose Load defaults and it did something then it said to reboot which I did when it rebooted it Also look here for other things to do, http://pcsupport.about.com/od/.....00007b.htm as well.

Not odd, until I point out that with at least most of the other components plugged in, I have to press the button 2-3 times to get the PC to start How do i run the hardware diagnostics? Where the confusing part comes in is the booting normally when you lean it over or hit it (very amusing btw :) ). Emachine Beep Codes Floppy powerconnector upside-down?

Immediately after entering key, I used "ALT" + "F10" keys at same time to get an access to Recovery Management Menu. Im not trying to incite a riot, just trying to get some help. I fixed my problem by installing new memory. http://www.tomshardware.com/forum/188620-30-emachine-boot but make sure flux is under good but not all over the place on the motherboard.

PC was still leaning - would not boot again. Emachine Laptop Wont Turn On I thought we had the same problem; however, I guess not. I will also provide pics if needed. Now it powers up just fine, the fans are flowing, the cd drive opens and closes, but the HD lights up one time then thats it.

Emachine Will Not Turn On

The only reason I won't delete this thread is because it has replies already. http://www.sevenforums.com/general-discussion/267297-emachine-wont-start-up.html Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. Emachine Desktop Wont Boot Up Should I mark this problem as solved? Emachines Black Screen On Startup if you can, then lease follow the instructions in the following link and post your logs in the thread you create (NOT in this thread): http://www.computerhope.com/forum/index.php/topic,46313.0.htmlIf you cannot, I suggest you

Computers shut down really fast when that happens. news I did NOT forget about you Larry, I just had a small down time while driving home from work ;) 0 derp 8 Years Ago Hey again, One thing I noticed as it is keyed to the eeprom on the emachines motherboard. Well, something happens... Emachines Laptop Screen Wont Turn On

Graphic Cards eMachine EL 1850 hang on start Win7 UltI have zero history of this box. Cheers, ~Mike :) 0 Gandolph 8 Years Ago I'm facing a very similar problem at the moment, and through my net research (which lead me here) I have discovered that (in Called emachine tech support, he told me to unplug everything a hold the power button for 30 seconds to clear the bios, but it didn't work. have a peek at these guys The problem you are having is with the mobo.

If it does, then you can plug things back in one at a time, (rebooting in between every device) and narrow the problem down to one thing. Emachines D620 Will Not Power On Even if that's not your power supply's model, it still a very distinct possibility that the mobo's been fried somehow. I turned it on and tapped F10 and F12 and nothing except the above messages.

It seems virus "disabled" recovery management.

Failing that, new MB AU $75.00 Caution : beware when flashing BIOS, it can crash system for good. Logged Allan ModeratorMastermind Thanked: 1166 Experience: Guru OS: Windows 7 Re: emachine won't boot up « Reply #1 on: January 29, 2011, 12:20:52 PM » What is new or different since and also it was old so it accumulated a lot of dirt... How To Start Emachine In Safe Mode I tried selecting the NVIDIA Boot Agent (try anything) during boot-up and receive a message "No boot filename received".

But if you want to save your emachine Recovery partition then I'd delete all but the Recovery partition during install, create a new partition for reinstall. Here is my system info and I have attached file as directed Both zipped together as System healthreport.zip AMD Athlon™ Processor 2850e (1.8GHz, 512KB L2 cache)Operating System2 : Genuine... The front processor light is lit like the PC is constantly 'working,' but nothing happens. check my blog Any help would be appreciated.

Im just desperate to fix this problem or at least save the HD. I have the access panel for after I had cleaned it out. Swapped out MB, same thing. Emachine w3611 Boot up error E-Machine Am37-L motherboard wont post,boot solved Emachines System Recovery CD/DVD freezes when I try to boot it up.

I've only just aquired this motherboard second hand, and the system ran fine for a week with no problems, but this morning, it took 30 min's to get the machine booted. The problem is that about … computer wont boot/ vga files 6 replies hey guys im new to this site so bare with , let me try to explain my problem... Yes, my password is: Forgot your password? We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Bingo! Good luck. Avadann_KedethJun 21, 2006, 3:03 AM I feel your pain. The motherboard is an FIC AM37 L, and the processor is an AMD Athlon AX2000DMT3C.

As for the hard drive the problem , if it is an IDE drive, make sure the jumper settings are set to master, and that none of the other drives on knucklehead replied Jan 20, 2017 at 8:37 AM A to Z of Items #5 knucklehead replied Jan 20, 2017 at 8:36 AM Ram upgrade for Notebook! You can't really tell though unless you swap out known working parts, including a CPU. So I redid the jumper thing with 'config' position and went through the steps again.

power issue or mobo fault Jul 9, 2012 Add New Comment You need to be a member to leave a comment. for toshiba portege laptop. Not a good combo.